Home > Pio Mode > Netbook HDD Stuck In Pio Mode

Netbook HDD Stuck In Pio Mode

Contents

I now consider this issue resolved, with the lesson learned to test performance after installing a new HDD before putting it into service. Check for new ones. 06-10-2010, 02:15 PM #3 cerealkillerxx Registered Member Join Date: Jun 2010 Posts: 7 OS: xp Quote: Originally Posted by Tikuf I really really don't After doing some more searching, I found out that the Intel Application Accelerator I recently installed is the culprit. Login to post comments Thanks Mon, 2013-06-03 08:01 by admin Glad that it helped. my review here

is it because my drivers aren't fully compatible with 7? Anyway it sounds like your Audio Card Drivers are not up todate, or using Microsoft Defult ones. Started by ultravy, August 14, 2012 11 posts in this topic ultravy    0 0 10 posts May 22, 2008 Country: Posted August 14, 2012 hi guys, i have a problem im running out of ideas! http://techlogon.com/2011/03/28/how-to-fix-hard-drive-stuck-in-pio-mode/

What Is Pio Mode

Somewhere at MS some of these bits can be looked up. I am sure I will learn a lot here in the future. I almost despaired. A typical symptom of PIO mode is slow data transfer, accompanied by high processor load, leading, for example, to a choppy video display.

General Discussion Stuck in safe modeHello, I have windows 7 home, and it keeps going into safe mode. Nothing changed.” (Would an easy fix be to replace certain drivers with Windows drivers?? Computer Help forum About This ForumCNET's forum on computer help is the best source for finding the solutions to your computer problems. Pio Mode 4 Still, I don't know what caused that and I'm sure there must be a better solution.

Flag Permalink This was helpful (0) Collapse - RE: On the fresh install of XP by akisame / November 15, 2008 5:21 AM PST In reply to: On the fresh install Pio Mode Windows 10 swiched back to dma and still get 3 mb/s write. Re-enable DMA using the Registry Editor This chapter describes the manual way to do what the quick solution at the top of this page does automatically through a script program. but less than 20 minutes with DMA.

When dragging a Capture in progress clip to and editor from Interplay window an error pops up "Exception: StreamingPlayConsumer::Executive Timeout. What Is Dma Mode My local shop put it together for me. This had me puzzled, until you explained it for me. Cheers!

Pio Mode Windows 10

resetdma.vbs ...and when I right-click on that file, windows displays an option to... Homepage Desensitize Your Computer's IDE or SATA Channels There's a bit more to it. What Is Pio Mode I'm desperate! Pio Mode Windows 7 Let's hope it stays this way.Anyone else thinks it's a HDD problem?

If you don't like the stock appearance of Google Home, here are two quick and easy ways to make it truly yours. Even if it turns out it's just the XP DMA bug and nothing else, you generally can't go wrong having a backup of important data. The only prior direct evidence I had regarding P0's slow performance were the differential copy speeds between it and the other two WD drives. For the most part it doesn't tell you what's actually happening in the computer either. Dma Mode Windows 10

in an ex-corporate PC) or has some corruption.Either way, you should be able to give yourself full permissions to the relevant key(s) - see http://techlogon.com/2012/11/26/how-to-change-permissions-of-a-registry-key/ for a guide to change the drive seems to be ok., no problems under the smart attributes! line. get redirected here However, the HD Tune image at the bottom is a bit troubling, so I'd be sure to hit the manufacturer's site and get their diagnostic program.

You can also subscribe without commenting. Sata Pio Mode due to a scratched CD) they may change into the older PIO mode.PIO is a vastly slower method of transferring data - even worse, the drive may get permanently ‘stuck' in If so, you likely have a hardware defect.

I was told it was a display issue and to uninstall and reinstall my display drivers.

I did write the quick solution program though. If you get a chance to swap the DVD burner for another one, even only temporarily for a test, you could try that. You want the highest possible DMA or Ultra DMA mode there, and you definitely don't want PIO mode. Windows 10 Dma The problem is my computer won't switch back to DMA.

This is a very basic registry edit that should fix the issue. Cleaning the registry and scanning for viruses were also unsuccessful. In this case, the user cannot turn on DMA for this device. HD Tune now gives both drives as 95 & 94Mb/sec respectively, an improvement on both!

For more than 6 months I suffered running under PIO mode…!! (Don't know why your page didn't show up 6 months ago… 😉 I think my trouble had started with a Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. Sign in to follow this Followers 1 HDD stuck in PIO mode?! You're my savior, unthinkable now that I had almost reinstalled the computer.

I've nothing much except my OS in the 500GB so if the worse case scenario happens, I won't really lose that much data.Hawkeye22: noted with thanks! Also, in case you need my computer specs you can find them here: http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&cc=us&docname=c00255589&dlc=en And yes, the hard drive is capable of Ultra DMA mode, as is the CD-RW/DVD drive I The posting of advertisements, profanity, or personal attacks is prohibited. As an added (and unexpected) bonus, I now understand the nature of the problem, why it happened, and why the solution provided fixed it.

ive checked everything! is it because the optical drives are from HP and Dell really hates that kinda s***? Register a new account Sign in Already have an account? First, make a backup of the registry.

Don't forg Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's You may well have caught the drive in the very early stages of failure. I'm desperate! "Intel Accelerator" program. It is a bit of a stretch to believe that two units from a reputable manufacturer of the same model and capacity are faulty.

In our example our device zero is ok.If Current Transfer Mode is set to Not Applicable there is no device present which is ok. However the issue (PIO / DMA ) is almost totally unknown by great majority of Windows users and therefore never mentioned.. Which ones?) So I tried the manual method by checking the mode of the secondary IDE port; after I click on the plus sign to the left of IDE ATA/ATAPI Controller, Upon the next boot, it reinstalled the IDE controller and the devices connected to it, and the drive was back in DMA mode once again.I would say that this should be